Just How to Install a Bath Tub Yourself: Removing and Replacing.
Book Appointment NowDo you find yourself looking for critical info on How to Install a Bathtub Yourself?
Installing a tub isn't specifically brain surgery, but it does call for solid plumbing, woodworking, and in some cases, tiling abilities. Replacing an old bath tub with a new one is likewise a reasonably challenging task. If the old tub is conveniently available, the job can move rapidly; if you need to open a wall surface to get rid of the old tub as well as place the new tub, the job is much harder. In either situation, the project is within a house handyman's abilities, although you will need an assistant to vacate the old tub as well as embeded in the new one. Ensure you have actually certified yourself for the task and are comfortable trying it. As opposed to hiring a specialist to take control of a halfway-completed project, it is much better to take into consideration using one before you begin. Possibilities are you might require an expert plumber to make tube links.
This article will assist you set up a brand-new bath tub in your bathroom if you have already gotten a brand-new bathtub and also do not need to alter the setup of your previous water pipes.
Your tools and material checklist must consist of the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you should do is disconnect the supply of water. After doing so, switch on the taps to drain pipes any kind of water remaining in the system. The process of removing the existing taps can be quite problematic due to the restricted access that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a fabric prepared for the staying water that will come from the pipes. Once the supply pipes have been removed, use the very same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning during this process. Once the taps have been removed, the holes in the bath/basin will need to be cleaned up of any type of old securing substance.
Before proceeding to fit the new taps, compare the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will certainly require a plastic port to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly need decreasing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, position the faucet in the placing hole in the bath/basin guaranteeing that the washers remain in area between the faucet and also the sink. Protect the tap in place with the manufacturer offered backnut. Once the faucet is safely in place, the supply pipes can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with regular faucet connectors. The previous kind ought to be attached to the tap ends initially, tightening just by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Mounting the Tub
Making use of both wood boards under its feet, place the bath tub in the needed position. The wood boards are practical in evenly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto 4 small factors.
The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by examining the spirit level and readjusting the feet on the bath tub up until the level checks out level.
To set up taps, fit the bottom of the outermost flexible faucet connector to the ideal supply pipe by making a compression sign up with; then do the very same for the other tap.
Switch on the water system and inspect all joints and new pipework for leakages and tighten them if needed. Load the bathtub as well as additionally inspect the overflow electrical outlet and also the normal electrical outlet for leakages.
Finally, take care of the bathroom paneling as described in the manufacturer's instruction manual. Tiling and also sealing around the tub must wait until the bathtub has actually been used a minimum of when as this will certainly settle it into its final setting.
Getting ready for the Installment
Firstly, the supporting framework provided with the bathroom should be fitted (if needed) according to the producer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to see to it that if the faucet features a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets unit to prevent strain on the tub.
Fit the versatile faucet adapters to the bottom of both faucets using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you utilize all of the supplied washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must currently prepare to be suited its last placement.
Tiling Around the Bath tub
In the location where the bathroom fulfills the tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to fracture an inflexible seal, creating the water to pass through the wall surface in between the bathroom as well as the tiling, causing issues with moisture and feasible leakages to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your fixtures and fittings. They are marketed in tubes and also cartridges, and also can sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of soaked newspaper or soft rope. Remember to constantly load the tub with water before sealing, to permit the activity experienced when the bathtub remains in usage. The sealer can break fairly early if you do not think about this activity before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise quickly available on the marketplace. It is a good idea to fit the ceramic tiles using waterproof or waterproof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our post about How to Install a Bathtub Yourself. Thanks a lot for finding the time to read our short article. Enjoyed reading our blog posting? Please share it. Let somebody else check it out. Thanks for your time invested reading it.
View